You may quickly and easily change your pants at home using blind hems.
The traditional cross-stitch technique used by manufacturers is prone to snags and folds coming undone, making it difficult to finish a project. Folding, pins, and sewing are all that is needed to produce an almost undetectable seam.
It is less vulnerable to wear and tear because of the zig-zag pattern of blind hem stitching, in which stitches alternate between the front and the back of the cloth.
With the help of this guide, you’ll never again have to hire a tailor or alteration expert to hem your trousers again, since you can do it yourself at home.
Is it simple to hem pants?
Hemming your own jeans is simple if you have access to a sewing machine. Get your stuff together. For this project, you’ll need the pair of trousers itself, a seam ripper, straight pins, a sewing mini iron and ironing board, a measuring tape or ruler, sewing scissors, a sewing machine, and thread that’s the same color as your pants.
Hemming Pants Requires the Use of Specific Tools
To blind hem trousers using a sewing machine, you’ll need the following supplies:
- Scissors
- A ruler is required.
- Pins
- A blind hem presser foot is included.
- A flat iron
- A marking pen or a bit of chalk, if desired.
Measuring
Measuring the pant length is the first step in hemming someone else’s trousers.
Make sure you have enough area to fold and get an idea of how long you want the new hem to be by placing the wearer on a stool.
To prevent the pants from coming undone while taking them off, fold the new hem outward rather than inward once it has been verified.
Try on the pants while standing up if you’re taking measurements for yourself. Try varying the fold’s size.
Take a moment to check your posture and make sure the fold is in the right place. Remove the pants after you’ve decided on the new hemline.
Marking and Cutting
Please make use of the marking pen or chalk that you have available. Unfold the trousers and use your ruler to make a straight line where you want your hem to fall.
Then, draw two parallel lines, one above and one below the hem. These two lines will be identical in distance from the original hemline, depending on how deep or shallow the alterations are.
So, if you want an inch-wide hem, mark a line an inch above and below the hem, respectively.
Trim the trousers to the point where just one inch remains below the third line with your scissors.
Pinning
Use your iron to press the trousers flat after folding them to match the new fold line. Pinning the fold of your hemline is essential before you start sewing.
Make sure your pants are dangling down. Take your fold and cuff it by flipping it back once. To observe a little lip of fabric stretched at the fold of the side seam, flip it back one more time. Using a horizontal pin, secure the fabric’s edge to the board.
Repeat this procedure on the other side of the pant leg. Another pin should be used at the halfway point to continue pinning around the cuff, folding back the cuff as you go.
By securing the fold in this manner, you’ll avoid having to undo and repeat stitching if you make any mistakes throughout the sewing process.
Preparing Your Equipment for Use
Load the bobbin with the thread of your choosing. To provide a smooth look, make sure the thread matches the color of the cloth.
Then, on the blind hem stitch, insert your blind hem foot. Next, depending on the width of your stitching, choose between a tiny or medium straight thread on your sewing machine.
Stitch count ranges from two to three on average.
How To Hem Pants With a Sewing Machine
Make sure the pin heads are on the proper side of your machine when you place your pant leg on it.
Before lowering the presser foot to the hem, make sure the incorrect side of your pant leg is facing out. Your presser foot should be right up against the fold while you’re pressing.
As your sewing machine does its magic, slowly let the leg to pass through the opening. Once a straight line is sewn around the perimeter of the leg, the machine will stop stitching. This should be done on the other leg as well.
Sewing carefully and deliberately will help you prevent any stitch abnormalities. It will alternate between stitching on the wrong side and stitching on the right side, going back and forth between the two sides of the cloth.
Only a little portion of the stitching on your pant legs will be visible.
The Hem is being Pressed
You may do this by spraying your hem with a little amount of water and pressing it firmly with your iron. A crease’s appearance will be lessened thanks to the water.
Try washing and drying your jeans if the crease still bothers you. The wrinkle will ultimately fade.
So there you have it: an easy way to get the perfect hem every time.
You may begin practicing hemming trousers with a sewing machine right now, now that you have a step-by-step tutorial to follow.
FAQ’s
What does it mean to get your pants hemmed?
A. Hemming is the process of shortening or extending a pair of pants, and the final edge of a pair of pants is referred to as the hem. An elegant, sophisticated appearance is achieved by having your pants hemmed to your specific height and style.
Is it possible to hem pants using a sewing machine?
A. The necessity to take your long pants to a seamstress is no longer necessary. If you have a sewing machine, you can do the hemming on your own legs. The ideal hem will be in your possession in no time if you have access to an electric sewing machine. Put your skills to the test on a couple pairs of trousers, and then offer to hem the pants of your friends.
What is the length of your hemmed pants?
A. Make sure the hem of your jeans covers around 2/3 to 3/4 of the laces on your shoes so that when you wear them there is enough cloth left to properly cuff them while still breaking once.
What is the most typical kind of stitch that would be utilized for a hem?
The slip stitch is another another flexible, almost invisible stitch that may be used on a double folded hem to give it a finished look. There are many steps involved, including passing the needle through one layer of fabric in 1/2″ stitches and emerging from the fold with just a little loop of cloth on the garment.
What is the most effective method of forming the hem?
Do not make the hem too thin so that it cannot be let down if necessary. Fold the hem up along the specified line, using pins at right angles to the edge every 2 to 3 inches to hold the hem in place. Keep the basting near to the fold. Make sure you try the item on to ensure that the length is right and that the hemline is level all the way around.
